Changelog between SNS v3.11 and v4.0
Removed commands
CONFIG SECURE
- CONFIG SECURE LIST
- CONFIG SECURE ADD
- CONFIG SECURE REMOVE
- CONFIG SECURE SYNC
- CONFIG SECURE STATE
- CONFIG SECURE SHOW
- CONFIG SECURE INITIALIZE
- CONFIG SECURE LOAD
- CONFIG SECURE BACKUP
- CONFIG SECURE RESTORE
CONFIG PROTOCOL NB-CIFS_TCP PROFILE IPS UUID
- CONFIG PROTOCOL NB-CIFS_TCP PROFILE IPS UUID SHOW
- CONFIG PROTOCOL NB-CIFS_TCP PROFILE IPS UUID INSERT
- CONFIG PROTOCOL NB-CIFS_TCP PROFILE IPS UUID REMOVE
- CONFIG PROTOCOL NB-CIFS_TCP PROFILE IPS UUID UPDATE
CONFIG PROTOCOL NB-EPMAP_TCP PROFILE IPS UUID
- CONFIG PROTOCOL NB-EPMAP_TCP PROFILE IPS UUID SHOW
- CONFIG PROTOCOL NB-EPMAP_TCP PROFILE IPS UUID INSERT
- CONFIG PROTOCOL NB-EPMAP_TCP PROFILE IPS UUID REMOVE
- CONFIG PROTOCOL NB-EPMAP_TCP PROFILE IPS UUID UPDATE
CONFIG PROTOCOL NB-SSN PROFILE IPS UUID
- CONFIG PROTOCOL NB-SSN PROFILE IPS UUID SHOW
- CONFIG PROTOCOL NB-SSN PROFILE IPS UUID INSERT
- CONFIG PROTOCOL NB-SSN PROFILE IPS UUID REMOVE
- CONFIG PROTOCOL NB-SSN PROFILE IPS UUID UPDATE
Commands replaced by another one
Commands with the same name that change behavior
CONFIG NETWORK ACTIVATE
Example: create a VLAN interface without physical interface attached
- Before:
SRPClient> CONFIG NETWORK ACTIVATE
100 code=00a00100 msg="Ok"
- After:
SRPClient> CONFIG NETWORK ACTIVATE
101CONFIG.NETWORK.INTERFACE.ADDRESS.ADD code=00a01000 msg="Begin" format="section_line"
[Check]
type=error code=6 interface=vlan0 msg="This VLAN has no physical interface"
200 code=02a0a300 msg="The network configuration has errors, it cannot be saved nor activated"
Checks are now done before activating the network configuration.
MONITOR HEALTH
- Before:
[<serial>]
hamode=
cpu=
disk=
fans=
mem=
powerstatus=
raid=
cert=
crl=
passwd=
[MAIN]
status=
- After:
[<serial>]
hamode=
cpu=
cpu_temp=
disk=
fans=
mem=
powerstatus=
raid=
cert=
crl=
passwd=
[MAIN]
status=
CONFIG HA SHOW
- Before:
[Global]
State=
Initialized=
Forward=
SendARP=
SendARPPeriod=
Secure=
InterfacesFlipFlop=
LACPWhenPassive=
ConnOlderThan=
LACPMembersHaveWeight=
[Communication]
ifname=
ifname2=
[ICMP]
NbPing=
[Corosync]
TokenTimeout=
MulticastAddr=
- After:
[Global]
State=
Initialized=
SendARP=
SendARPPeriod=
Secure=
InterfacesFlipFlop=
LACPWhenPassive=
DelayConnUpd=
LACPMembersHaveWeight=
[Communication]
ifname=
ifname2=
[ICMP]
NbPing=
[Corosync]
TokenTimeout=
MulticastAddr=
Commands with new mandatory parameters
Commands with new optional parameters
CONFIG FILTER RULE UPDATE
- nohasync (on|off) (no default value)
- etherproto (auto|none|<transport protocol name>) (no default value)
CONFIG NETWORK INTERFACE SHOW
- useclone (on|off) (default: off)
CONFIG NETWORK INTERFACE UPDATE
-
name (no default value)
PARAMETERS FOR ETHERNET, AGG, VLAN, GRETAP AND BRIDGE INTERFACES
-
DHCPLeaseTime (no default value)
-
DHCPHostName (no default value)
-
DHCPVendorClassId (no default value)
-
DHCPUserClass (no default value)
-
DHCPAuthsend (no default value)
-
RequestDNS (on|off)
CONFIG NETWORK INTERFACE IPV6 ADDRESS UPDATE
- refaddress (no default value)
CONFIG NETWORK INTERFACE IPV6 ROUTERADV PREFIX UPDATE
- refaddress (no default value)
CONFIG HA CREATE
- DelayConnUpd
(replaces ConnOlderThan)
CONFIG HA UPDATE
- DelayConnUpd
(replaces ConnOlderThan)
PKI SEARCH
- scope (local|global|both)
- Before: local
- After: both by default